医用防辐射铅玻璃直线直边机的使用
    2019-1-25 16:42:40  文章来源:http://www.jnlzsb.com
    医用防辐射铅玻璃直线直边机的使用
    Application of Medical Radiation-proof Lead Glass Straight Line Edge Machine
    直边就是垂直于镜面,斜边就是磨出一个与镜面成10度左右的斜面来,外观愈加时髦,美观。不同厚度的医用铅玻璃的深加工:切割,磨边,抛光边,斜边,异型边的制造等。
    The straight side is perpendicular to the mirror, and the oblique side is to grind an oblique surface about 10 degrees from the mirror. The appearance is more fashionable and beautiful. Deep processing of medical lead glass with different thickness: cutting, grinding, polishing, beveling, special-shaped edge manufacturing, etc.
    医用铅玻璃磨削直线边:按相关尺寸调整好磨边导向板,使之颠簸,灵敏的沿着导向板作直线往复运动,使磨轮与板边接触,并有适宜的磨削量,然后翻开水阀使冷水放射到磨轮上,启动电源开关使磨轮运转正常后,即可操纵磨机沿着道轨匀速停止磨削。从而到达医用铅玻璃磨削直线边的目的。如需求磨斜边,可随意调零件头角度。 医用铅玻璃磨削曲线、圆弧边:不必道板,只需纯熟操作磨机沿着曲线板坯边停止磨削,如系正圆形,可固定好圆心于板中心,使磨机沿此中心作圆周运动即可加工出标准的正圆形产品,其它工序加工办法与磨直边相反。

    Medical Lead Glass Grinding Linear Edge: Adjust the Grinding Edge Guiding Plate according to the relevant size, make it bump, move sensitively along the guide plate in a straight line, make the grinding wheel contact with the edge of the plate, and have appropriate amount of grinding, then turn on the water valve to radiate cold water to the grinding wheel, start the power switch to make the grinding wheel run normally, then control the grinding machine to stop grinding along the track at a uniform speed. Thus, the purpose of grinding the straight edge of medical lead glass is achieved. If you need to grind the bevel edge, you can adjust the angle of the part head at will. Medical Lead Glass Grinding Curve and Arc Edge: It is not necessary to use a traveling board, but only skillfully operate the grinder to stop grinding along the edge of the curve slab. If it is a regular circle, the center of the circle can be fixed in the center of the plate, so that the grinder can move around the center to produce a standard regular circular product. The other processing methods are opposite to the grinding straight edge.

    射线防护器材

    医用铅玻璃操直线直边机作留意事项与维护颐养
    Cautions and Maintenance of Medical Lead Glass Linear Straight Side Machine
    1、操作前应反省电缆线能否残缺,有无破损漏电景象,电器能否受潮,用户线路中必需装置漏电保安器。
    1. Before operation, it is necessary to reflect on whether the cable is incomplete, whether there is a damaged leakage phenomenon, whether the electrical appliances can be damped, and whether the leakage protector must be installed in the user's line.
    2、操作时应戴绝缘手套,避免发作不测。
    2. When operating, insulating gloves should be worn to avoid unexpected attacks.
    3、磨削时必需有足够压力的冷却水,以保证磨削的效率与磨轮的运用寿命。
    3. In order to ensure the grinding efficiency and the service life of grinding wheels, cooling water with sufficient pressure must be provided during grinding.
    4、运用进程中如转速突然急剧降低,应减小磨机压力,尽量不要超负荷运用,否则易损坏电机。常常反省碳刷,留意改换,以防磨伤转子。
    4. In the process of operation, if the speed suddenly drops sharply, the mill pressure should be reduced, and the overload operation should be avoided as far as possible, otherwise the motor will be easily damaged. Often reflect on the carbon brush, pay attention to change, in order to prevent wear and tear the rotor.
    本文由济南联众供热设备厂http://www.jnlzsb.com整理,更多射线防护器材知识,欢迎关注我们,谢谢!!
    This article is organized by Jinan Lianzhong Heating Equipment Factory at http://www.jnlzsb.com. More knowledge of radiation protection equipment, welcome to pay attention to us, thank you!!